[BC] Remote Control Access via Internet

[Bailey, Scott]

I have Verizon, so I think the same applies here as well.

But this is what I'm thinking Chris, why spend the money on a Burk
ARC-16, when my automation system can do this. I'm using Digital Juke
Box, and Jim Barcus has a program that can send you an email if
something goes wrong with any part of DJB or if an event didn't occur.

Scott

-----Original Message-----
From: broadcast-bounces at radiolists.net
[mailto:broadcast-bounces at radiolists.net] On Behalf Of Chris Oradat
Sent: Wednesday, February 21, 2007 11:59 AM
To: 'Broadcasters' Mailing List'
Subject: RE: [BC] Remote Control Access via Internet

Most remote controls that allow TCP/IP connections have a provision for
e-mailing alerts.  If you can adjust what is sent out, that message can
be
sent to a cell phone.  It just requires knowing the e-mail address of
the
phone.  For at least two providers (Cingular, T-Mobile), this is
included
with text messaging.

-----Original Message-----
From: broadcast-bounces at radiolists.net
[mailto:broadcast-bounces at radiolists.net] On Behalf Of Glen Kippel
Sent: Wednesday, February 21, 2007 11:52 AM
To: Broadcasters' Mailing List
Subject: Re: [BC] Remote Control Access via Internet

You will need to have some way of having it contact you if something
falls
out of tolerance.  How you do this is up to you, and if you get
inspected,
be prepared to show how/that it works.  I don't know about internet,
having
used only dialup and/or SCA remote control, but at my previous station I
had
the ARC-16 call if the output power fell below 90% (this could be
optional),
rose above 105% (this is not), and if the ModMinder (R) showed
consistently
over modulation.  Of course, we had other things that are not
FCC-required,
like if the AC power was off, the building temperature got above 95
degrees,
or we lost an STL -- stuff like that.  You do not have to remotely
monitor
plate voltage, plate current, etc. unless you want to.  It can be handy
to
know these things before you get to the transmitter site, but the FCC
doesn't require it.

On 2/21/07, Bailey, Scott <sbailey at nespower.com> wrote:
>
> Question to the brain trust:
>
>
>
> I've read over the rules of unattended operation, and I have a
question.
> Does a station have to have a dial up phone line installed at the
> transmitter for remote control or can a station control it transmitter
> by internet access only, and do away with the dial up phone line?
>
>
>
> My thoughts were, and a discussion with another engineer was, the last
> update of the remote control rules was around 1995, almost 12 years
ago,
> before we had wide open internet access.  My studio is with the
> transmitter, and I can access my studio automation with my pocket pc,
> via Verizon Broadband Wireless, or even Wi-fi. My studio automation
can
> lower and raise power on my transmitter, and turn it off. I can access
> my automation system via logmein.com at home and control the
transmitter
> as well.
>
>
>
> What are the thoughts you guys have on this subject?  Do we really
have
> to have a "dedicated" phone line at the transmitter, if I'm using that
> line for DSL service and my pc controls the transmitter, and I have
> constant access to it?
>
>
>
> Scott
>
> _______________________________________________
>
> The BROADCAST [BC] list is sponsored by SystemsStore On-Line Sales
> Cable-Connectors-Blocks-Racks-Wire Management-Test Gear-Tools and
More!
> www.SystemsStore.com       Tel: 407-656-3719    Sales at SystemsStore.com
>
>
_______________________________________________

The BROADCAST [BC] list is sponsored by SystemsStore On-Line Sales
Cable-Connectors-Blocks-Racks-Wire Management-Test Gear-Tools and More! 
www.SystemsStore.com       Tel: 407-656-3719    Sales at SystemsStore.com

_______________________________________________

The BROADCAST [BC] list is sponsored by SystemsStore On-Line Sales
Cable-Connectors-Blocks-Racks-Wire Management-Test Gear-Tools and More! 
www.SystemsStore.com       Tel: 407-656-3719    Sales at SystemsStore.com